Jan 05

ACRYLOC PATCH

PRODUCT TYPE PACKAGING NOMINAL WEIGHT
Texture Coats 5L, 10L, 15L Heavy Duty Plastic Pail 8.5kg, 17kg, 25kg respectively

 DESCRIPTION

Forming part of the Wallcote system, Acryloc Patch is a durable, water based material for patching, filling and skim coating on a wide range of substrates.

Acryloc Patch is composed of finely graded sand and fillers in a water based acrylic emulsion processed with proprietary additives, extenders and a powerful fungicide/ anti-mildew agent.

Acryloc Patch may also be used for setting butt joints and beads/trims with the addition of 5-10% Portland Cement.

 FEATURES & BENEFITS

Excellent water resistance Prime
Excellent vapour permeability Acryloc Prime Seal
Excellent flexibility Joint Set & Beads/Trims
Excellent crack resistance Acryloc Patch (add 5-10% cement)
Excellent durability Fill / Patch / Skim
Strong adhesion Acryloc Patch
Easy to apply Render Coat (if required)
Water based Wallcote FR, for AAC, polymer modified, fibre reinforced
10 yr Coating System warranty Wallcote Pro Render, polymer modified, low – medium build
Easy & safe clean up Wallcote Trade Render, traditional Render, medium – high build
plus Acryloc Liquid Bond (if specified)
Texture (if required)
Acryloc Marblecote Medium or Coarse
(or) Sandcote Fine / Medium / Coarse
(or) Trowel On Scratch
(or) Tuscan Fine/Moroccan Med./Rustic Coarse
Protective Colour Coat (recommended)
Acryloc Armourflex Masonry Matt or Lo Sheen
(must prime Render Coat if no texture applied)

 SUITABLE SUBSTRATES – when properly prepared

  • Cement Render
  • AAC (Autoclaved Aerated Concrete)
  • Fibre Cement Sheeting (Fibro/Blue board)
  • Rendered expanded polystyrene
  • Clay and Concrete Brickwork
  • Tilt panel walls
  • Other primed exterior surfaces

SUBSTRATE PREPARATION

  • Areas not to be coated should be masked and protected
  • All surfaces to be coated must be clean, sound, free from contaminants including; oil, mould release, dust, dirt, silicone, mud, grease, salt, efflorescence, animal droppings and any loose or flaking material.
  • All substrates must be primed, normally with Acryloc Prime Seal.
  • Apply the Prime Seal at the rate of 12.5-16.5m2/L and allow to dry (approx 30mins).
  • (Note: The concentrate form of Prime Seal must be diluted before use).

APPLICATION

  • Acryloc Patch does not require thinning but mixing with a power stirrer will enhance workability and coverage.
  • For setting of Joints or installation of Beads and Trims, add Portland Cement to the pail as per the following table:
Pail Size Cement Addition
5 Litre 350g to 700g
10 Litre 700g to 1.4kg
15 Litre 1kg to 2kg

Caution: Excess quantity of cement can cause the product to have a reduced pot life and hamper application, workability and durability. Do not thin after addition of cement.

  • Mix thoroughly with a broad, flat stirrer, using an upward lifting action, or power mixer.

Setting Joints (use Acryloc Patch with added Cement)

  • Apply a 2mm layer of Acryloc Patch into the recessed joint.
  • Apply a single strip of alkali resistant fiberglass tape and trowel into the freshly applied material.
  • When the tape is fully bedded, skim over with one (1) further coat of Acryloc Patch, feathering edges as neatly as possible.

Beads & Trims (use Acryloc Patch with added Cement)

Either,

  • Use Acryloc Patch to fix the trim by fully coating the inside of the trim with Acryloc Patch, pressing firmly into place and trowelling off the outside of the trim to ensure that all holes are filled; Or, if the trim is already fixed in place,
  • Apply Acryloc Patch to the trim, trowelling it into the holes to ensure that there are no voids.

Skim Coating

  • Apply Acryloc Patch to the surface to a thickness of approx 1.5mm.
  • Where the entire surface is being skim coated, commence at the top of the wall panel. Two (2) or more applicators may be required for large uninterrupted wall areas.
  • Allow surface to stand for a short time prior to finishing.
  • Rub up or ‘finish’ with a suitable float either in a vertical or circular fashion, terminating only when a whole area or section is completely coated.
  • Typically one (1) coat should be adequate if the substrate is flatt and level, but a second coat may be applied if required.

Important Notes

  • Care should be taken to keep Acryloc Patch off windows and adjacent surfaces that are not to be coated, as it can be very difficult to remove once allowed to dry.
  • Acryloc Patch must be over coated using the appropriate components selected from the Wallcote system.
  • Do not apply Acryloc Patch when rain is anticipated within 5 hours of completion of the days work, longer in damp, cold +/or humid conditions.
  • Avoid application in full sun, on hot surfaces or in hot windy conditions.
  • Application should be carried out on a day with temperatures above 10°C and below 32°C.
  • Coated area must be protected from damage until the completion of the project; finished work must be protected from rain, frost and severe weather conditions until fully dried.

OTHER CONSIDERATIONS

Shelf-Life – Unopened Containers

Maximum two (2) years from date of manufacture when stored correctly.

Transport & Storage

Pails should not be stacked more than three (3) high during transportation and must be transported upright Store in a cool place, upright, out of direct sunlight and above 4°C.
For further information refer to MSDS for Acryloc Patch.

TECHNICAL DATA

APPEARANCE Milky white, gritty, viscous liquid
ODOUR Low
APPLICATION METHODS Trowel
SPECIFIC GRAVITY (NOMINAL) ~1.5
THEORETICAL COVERAGE 0.7-0.8m2/L single coat, 10-12 m2per 15L pail
WET FILM THICKNESS (RECOMM) 1.3-1.5mm single skim coat, ~4mm in joints
DRY TIME (25°C & 50% RH) (APPROX) Tack Free Recoat/Overcoat Fully Dried
2 hours After 4 hours 48 hours
NO. OF COATS Typically 1 coat
GLOSS LEVEL Matt – textured

 WARRANTY

Acryloc Building Products provides a material replacement warranty against bubbling, peeling or flaking of the full Wallcote Coating System caused by any defect in manufacture for a period of ten years when applied correctly by a skilled and experienced applicator in accordance with all current application criteria, including but not limited to, substrate type and preparation, application rates and methods, prevailing weather conditions and protection of finished work.

Application dates, product batch numbers and quantities must be recorded and supplied as a minimum to effect potential product failure investigation.

Acryloc Building Products provides no warranty, expressed or implied, against damage due to movement of the substrate or structure.

Acryloc Building Products cannot accept responsibility for variations in colour, strength, appearance or workability resulting from on-site mixing procedures and conditions.

SAFETY & HANDLING

When working with Acryloc Patch observe the usual precautions for handling acrylic water based products including:

Avoid inhalation of the vapour, prolonged skin contact and particularly eye contact.

Wear protective clothing to minimize skin contact and wear goggles where splatter is likely.

Where spills occur, soak up liquid spillage with sand/sawdust and dispose of in a sensible manner. Do not permit run-off to sewer, storm water or open bodies of water.

Full pails are HEAVY. Wear protective footwear and seek assistance if necessary.

 FIRST AID MEASURES

If swallowed, wash out mouth with water. Do NOT induce vomiting. Drink at least two (2) glasses of water. Seek medical attention.

Eye

Wash with copious amount of water for 15 minutes holding eyelid(s) open. Take care not to rinse contaminated water into non-affected eye. Seek medical attention.

Advice to Doctor
Treat symptomatically.
Find Out More

Jan 05

ACRYLOC EXTERIOR PRIMER

PRODUCT TYPE PACKAGING NOMINAL WEIGHT
Texture Coats 5L, 20L Heavy Duty Plastic Pail 6.5kg, 25.5kg respectively

DESCRIPTION

Acryloc Exterior Primer is a good quality, Low Odour, Exterior Primer, suitable for most external surfaces including, cement render, fibrous-cement sheet, softwood, masonry including brick, block & off form concrete.

Acryloc Exterior Primer is easy to apply and fast drying making it ideal for residential, commercial and industrial developments.

FEATURES & BENEFITS

  • Low Odour
  • Easy to apply, low spatter formula
  • Excellent adhesion
  • Water based, Easy & safe clean up
  • High hiding power
  • Can be tinted

SUBSTRATE PREPARATION – paint will not adhere to a surface that is dirty.

  • Areas not to be coated should be masked and protected.

New Unpainted Surfaces
Fill nail holes, cracks and imperfections with an appropriate patching material and sand smooth.

Remove dust and make sure that the surface is clean, sound and free from contaminants such as oil, mould release, silicone, grease and efflorescence.

Previously painted surfaces
Wash down with sugar soap and rinse with clean water.

Check for soundness of the original coating, remove any loose or flaking paint, fill holes and cracks and sand smooth.

Gloss or Semi-Gloss finishes must be completely dulled by sanding.

APPLICATION

  • Mix thoroughly and check that the colour (if tinted) is correct before commencing work.

Method

  • Apply 1 full even coat of Acryloc Exterior Primer by brush, spray or roller.
  • For Roller application, a medium nap (12mm) roller is recommended; use a larger nap (25mm on rough surfaces).

High quality synthetic rollers give best performance. Use a 13 or 15 thou spray tip with Airless spray.

Important Notes

  • Care should be taken to keep Acryloc Exterior Primer off windows and adjacent surfaces that are not to be coated.
  • Application should be carried out on a day with temperatures above 10°C and below 32°C.

Clean-Up

Clean up with water

OTHER CONSIDERATION

Shelf-Life – Unopened Containers

Maximum two (2) years from date of manufacture when stored correctly.

Transport & Storage

Pails should not be stacked more than three (3) high during transportation and must be transported upright.
Store in a cool place, upright, out of direct sunlight and above 4°C
For further information refer to MSDS for Acryloc Exterior Primer

TECHNICAL DATA

APPEARANCE Viscous white liquid
ODOUR Low
RESIN TYPE Styrene Acrylic Emulsion
APPLICATION METHOD Roller, brush, spray
SPECIFIC GRAVITY (NOMINAL) 1.28
VOLUME SOLIDS (APPROX) 29%
WEIGHT SOLIDS (APPROX) 44%
THEORETICAL COVERAGE 12-16 m2/L per coa
WET FILM THICKNESS (RECOMM) 80-100 microns per coat
DRY FILM THICKNESS (MIN) 23-29 microns per coat
DRY TIME (25°C & 50% RH)
(APPROX)
Tack Free Recoat/ Overcoat Fully Dried
2 hours After 3 hours 24 hours
NO. OF COATS 1 coat is recommended
GLOSS LEVEL Flat
SOLVENT FOR CLEANING Water
FLAMMABILITY Non-flammable

SAFETY & HANDLING

When working with Acryloc Exterior Primer observe the usual precautions for handling acrylic water based products including:

  • Avoid inhalation of the vapour, prolonged skin contact and particularly eye contact.
  • Wear protective clothing to minimize skin contact and wear goggles where splatter is likely.
  • Where spills occur, soak up liquid spillage with sand/sawdust and dispose of in a sensible manner. Do not permit run-off to sewer, storm water or open bodies of water.

Full pails are HEAVY. Wear protective footwear and seek assistance if necessary.

FIRST AID MEASURES

If swallowed, wash out mouth with water. Do NOT induce vomiting. Drink at least two (2) glasses of water. Seek medical attention.

Eye

Wash with copious amount of water for 15 minutes holding eyelid(s) open. Take care not to rinse contaminated water into non-affected eye. Seek medical attention.

Advice to Doctor

Treat symptomatically

Find Out More

Jan 05

ACRYLOC SANDCOTE

PRODUCT TYPE PACKAGING NOMINAL WEIGHT
Texture Coats 5L, 15L Heavy Duty Plastic Pail 7.5kg, 23kg respectively

DESCRIPTION

Forming part of the Wallcote system, Acryloc Sandcote textures are durable, sand based coatings; ideal for providing an attractive finish on correctly prepared domestic & commercial, exterior & interior wall surfaces.

Acryloc Sandcote textures are available in three grain sizes coatings, manufactured as tintable, white bases.

Acryloc Sandcote can be applied by trowel or by spraying.

FEATURES & BENEFITS

Excellent water resistance Prime
Excellent vapour permeability Acryloc Prime Seal
Excellent flexibility Joint Set & Beads/Trims (if required)
Excellent crack resistance Acryloc Patch (add 5-10% cement)
Excellent durability Fill / Patch / Skim (if required)
Strong adhesion Acryloc Patch
Low maintenance Render Coat (if required)
Easy to apply Wallcote FR, for AAC, polymer modified, fibre reinforced
Water based Wallcote Pro Render, polymer modified, low – medium build
10 yr Coating System warranty Wallcote Trade Render, traditional Render, medium – high build
Easy & safe clean up plus Acryloc Liquid Bond (if specified)
Tintable Texture
Sandcote Fine / Medium / Coarse Texture
Protective Colour Coat (recommended)
Acryloc Armourflex Masonry Matt or Lo Sheen

 SUITABLE SUBSTRATES – when properly prepared

  • Cement Render.
  • AAC (Autoclaved Aerated Concrete).
  • Fibre Cement Sheeting (Fibro/Blue board).
  • Rendered expanded polystyrene.
  • Clay and Concrete Brickwork.
  • Concrete blocks.
  • Tilt panel walls.
  • Other primed exterior surfaces.

SUBSTRATE PREPARATION

  • Areas not to be coated should be masked and protected.
  • All surfaces to be coated must be clean, sound, free from contaminants including; oil, mould release, dust, dirt, silicone, mud, grease, salt, efflorescence, animal droppings and any loose or flaking material.
  • All substrates must be primed with Acryloc Prime Seal.
  • Apply the Prime Seal at the rate of 12.5-16.5m2 /L and allow to dry (approx 30mins).
  • (Note: The concentrate form of this product must be diluted before use)
  • Imperfections and butt joints can be filled with Acryloc Patch with 5% Portland Cement added.
  • The surface may be coated with Acryloc Patch or Acryloc cement based Render, as required, before applying Acryloc Sandcote.

APPLICATION

  • Acryloc Sandcote does not require thinning or dilution. Up to 300mL of clean water can be added to a 15L pail to adjust the workability if desired.
  • Mix thoroughly with a broad, flat stirrer, using an upward lifting action, or use a power mixer.
  • Power mixing is recommended as this will enhance the workability and give the best coverage.
  • A wet edge should be maintained throughout the application and day joints formed at corners, expansion joints or mouldings where they will not be evident after completion.

Trowel on application

  • Apply Acryloc Sandcote to the surface, trowelling to the thickness of the largest particle.
  • Commence at the top of the wall panel. (Two or more applicators may be required for large uninterrupted wall areas).
  • Allow surface to stand for a short time prior to finishing.
  • Rub up or ‘finish’ with a suitable texture float either in a vertical or circular pattern depending on the desired finish and profile.
  • Application must be carried out in a brisk uniform fashion, terminating only when a whole area or section is completely coated. For example; a natural break, expansion joint or corner.
  • Acryloc Sandcote should not be extended (spread) too far; otherwise durability and hiding power may suffer.

Spray on application

  • Hopper gun, pressure pot or diaphragm pump system can be used to produce a fine supple texture or high-build chunky texture.

Important Notes

  • Care should be taken to keep Acryloc Sandcote off windows and adjacent surfaces that are not to be coated, as it can be very difficult to remove once allowed to dry.
  • Do not apply Acryloc Sandcote when rain is anticipated within 5 hours of completion of the days work, longer in damp, cold +/or humid conditions.
  • Avoid application in full sun, on hot surfaces or in hot windy conditions.
  • Application should be carried out on a day with temperatures above 10°C and below 32°C.
  • Coated area must be protected from damage until the completion of the project; finished work must be protected from rain, frost and severe weather conditions until fully dried.
  • Acryloc Sandcote is normally over coated with Acryloc Acryloc Armourflex for best colour accuracy, to improve durability and to reduce dirt pickup.

Clean-Up
Clean up with water.

OTHER CONSIDERATIONS

Shelf-Life – Unopened Containers

Maximum two (2) years from date of manufacture when stored correctly.

Transport & Storage

Pails should not be stacked more than three (3) high during transportation and must be transported upright.
Store in a cool place, upright, out of direct sunlight and above 4°C.
For further information refer to MSDS for Acryloc Sandcote.

 TECHNICAL DATA

APPEARANCE Off white textured viscous liquid
ODOUR Low
APPLICATION METHOD Spray, trowel
SPECIFIC GRAVITY (NOMINAL) ~1.5
THEORETICAL COVERAGE 1-1.2m²/L Fine; 0.8-0.9m²/L Medium; 0.7-0.9m²/L Coarse
WET FILM THICKNESS (RECOMM) Product grain size
DRY TIME (25°C & 50% RH)(APPROX) Tack Free Recoat/ Overcoat Fully Dried
2 hours After 3 hours 24 hours
NO. OF COATS Typically 1 coat
GLOSS LEVEL Matt – low gloss

 WARRANTY

Acryloc Building Products provides a material replacement warranty against bubbling, peeling or flaking of the full Wallcote Coating System caused by any defect in manufacture for a period of ten years when applied correctly by a skilled and experienced applicator in accordance with all current application criteria, including but not limited to, substrate type and preparation, application rates and methods, prevailing weather conditions and protection of finished work.
Application dates, product batch numbers and quantities must be recorded and supplied as a minimum to effect potential product failure investigation.

Acryloc Building Products provides no warranty, expressed or implied, against damage due to movement of the substrate or structure.

Acryloc Building Products cannot accept responsibility for variations in colour, strength, appearance or workability resulting from on-site mixing procedures and conditions.

SAFETY & HANDLING

Observe the usual precautions for handling acrylic water based products including:

  • Avoid inhalation of the vapour, prolonged skin contact and particularly eye contact
  • Wear protective clothing to minimize skin contact and wear goggles where splatter is likely
  • Where spills occur, soak up liquid spillage with sand/sawdust and dispose of in a sensible manner. Do not permit run-off to sewer, storm water or open bodies of water.

Full pails are HEAVY. Wear protective footwear and seek assistance if necessary.

FIRST AID MEASURES

If swallowed, wash out mouth with water. Do NOT induce vomiting. Drink at least two (2) glasses of water. Seek medical attention.

Eye

Wash with copious amount of water for 15 minutes holding eyelid(s) open. Take care not to rinse contaminated water into non-affected eye. Seek medical attention.

Advice to Doctor

Treat symptomatically

Find Out More

Jan 05

ACRYLOC MARBLECOTE

PRODUCT TYPE PACKAGING NOMINAL WEIGHT
Texture Coats 5L, 15L Heavy Duty Plastic Pail 7.5kg, 23kg respectively

DESCRIPTION

Forming part of the Wallcote system, Acryloc Marblecote is a durable marble based texture coating, ideal for providing an attractive finish on correctly prepared domestic & commercial, exterior & interior wall surfaces.

Acryloc Marblecote is available in two grain sizes and is manufactured as tintable, white bases.
Acryloc Marblecote can be applied by trowel or by spraying.

Excellent water resistance Prime
Excellent vapour permeability Acryloc Prime Seal
Excellent flexibility Joint Set & Beads/Trims (if required)
Excellent crack resistance Acryloc Patch (add 5-10% cement)
Excellent durability Fill / Patch / Skim (if required)
Strong adhesion Acryloc Patch
Low maintenance Render Coat (if required)
Easy to apply Wallcote FR, for AAC, polymer modified, fibre reinforced
Water based Wallcote Pro Render, polymer modified, low – medium build
10 yr Coating System warranty Wallcote Trade Render, traditional Render, medium – high build
Easy & safe clean up plus Acryloc Liquid Bond (if specified)
Tintable Texture Coat
Acryloc Marblecote Medium or Coarse
Protective Colour Coat (recommended)
Acryloc Armourflex Masonry Matt or Lo Sheen

 SUITABLE SUBSTRATES – when properly prepared

  • Cement Render
  • AAC (Autoclaved Aerated Concrete)
  • Fibre Cement Sheeting (Fibro/Blue board)
  • Rendered expanded polystyrene
  • Clay and Concrete Brickwork
  • Concrete blocks
  • Tilt panel walls
  • Other primed exterior surfaces

SUBSTRATE PREPARATION

  • Areas not to be coated should be masked and protected
  • All surfaces to be coated must be clean, sound, free from contaminants including; oil, mould release, dust, dirt, silicone, mud, grease, salt, efflorescence, animal droppings and any loose or flaking material
  • All substrates must be primed with Acryloc Prime Seal.
  • Apply the Prime Seal at the rate of 12.5-16.5m2/L and allow to dry (approx 30mins)

(Note: The concentrate form of Prime Seal must be diluted before use)

  • Imperfections and butt joints can be filled with Acryloc Patch with 5% Portland Cement added.
  • The surface may be coated with Acryloc Patch or Acryloc cement based Render, as required, before applying Acryloc Marblecote.

APPLICATION

  • Acryloc Marblecote does not require thinning or dilution. Up to 300mL of clean water can be added to a 15L pail toadjust the workability if desired.
  • Mix thoroughly with a broad, flat stirrer, using an upward lifting action, or use a power mixer.
  • Power mixing is recommended as this will enhance the workability and give the best coverage.
  • A wet edge should be maintained throughout the application and day joints formed at corners, expansion joints or mouldings where they will not be evident after completion.

Trowel on application

  • Apply Acryloc Marblecote to the surface trowelling to the thickness of the largest particle
  • Commence at the top of the wall panel. (Two or more applicators may be required for large uninterrupted wall areas).
  • Allow the surface to stand for a short time prior to finishing
  • Rub up or ‘finish’ with a suitable texture float either in a vertical or circular pattern depending on the desired finish and profile.
  • Application must be carried out in a brisk uniform fashion, terminating only when a whole area or section is completely coated. For example; a natural break, expansion joint or corner.
  • Acryloc Marblecote should not be extended (spread) too far; otherwise durability / hiding power may suffer.

Spray on application

  • A Hopper gun, pressure pot or diaphragm pump system can be used to produce a fine supple texture or high-build chunky texture.

Important Notes

  • Care should be taken to keep Acryloc Marblecote off windows and adjacent surfaces that are not to be coated, as it can be very difficult to remove once allowed to dry.
  • Do not apply Acryloc Marblecote when rain is anticipated within 5 hours of completion of the days work, longer in damp, cold +/or humid conditions.
  • Avoid application in full sun, on hot surfaces or in hot windy conditions.
  • Application should be carried out on a day with temperatures above 10°C and below 32°C.
  • Coated area must be protected from damage until the completion of the project; finished work must be protected from rain, frost and severe weather conditions until fully dried.
  • Acryloc Marblecote is normally over coated with Acryloc Acryloc Armourflex for best colour accuracy, to improve durability and to reduce dirt pickup.

Clean-Up

Clean up with water.

OTHER CONSIDERATIONS

Shelf-Life – Unopened Containers

Maximum two (2) years from date of manufacture when stored correctly.

Transport & Storage

Pails should not be stacked more than three (3) high during transportation and must be transported upright.

Store in a cool place, upright, out of direct sunlight and above 4°C.
For further information refer to MSDS for Acryloc Marblecote.

TECHNICAL DATA

   APPEARANCE Off white textured viscous liquid
   ODOUR Low
APPLICATION METHOD Spray, trowel
SPECIFIC GRAVITY (NOMINAL) 1.5 -1.7
THEORETICAL COVERAGE 0.7-0.9m /L
WET FILM THICKNESS (RECOMM) Product grain size
DRY TIME (25°C & 50% RH)
(APPROX)
Tack Free Recoat/ Overcoat Fully Dried
1 hours After 3 hours 24 hours
   NO. OF COATS Typically 1 coat
   GLOSS LEVEL Matt – low gloss

 WARRANTY

  • Acryloc Building Products provides a material replacement warranty against bubbling, peeling or flaking of the full Wallcote Coating System caused by any defect in manufacture for a period of ten years when applied correctly by a skilled and experienced applicator in accordance with all current application criteria, including but not limited to, substrate type and preparation, application rates and methods, prevailing weather conditions and protection of finished work.
  • Application dates, product batch numbers and quantities must be recorded and supplied as a minimum to effect potential product failure investigation.
  • Acryloc Building Products provides no warranty, expressed or implied, against damage due to movement of the substrate or structure.
  • Acryloc Building Products cannot accept responsibility for variations in colour, strength, appearance or workability resulting from on-site mixing procedures and conditions.

SAFETY & HANDLING

When working with Acryloc Marblecote observe the usual precautions for handling acrylic water based products including:

  • Avoid inhalation of the vapour, prolonged skin contact and particularly eye contact
  • Wear protective clothing to minimize skin contact and wear goggles where splatter is likely
  • Where spills occur, soak up liquid spillage with sand/sawdust and dispose of in a sensible manner. Do not permit run-off to sewer, storm water or open bodies of water

Full pails are HEAVY. Wear protective footwear and seek assistance if necessary.

FIRST AID MEASURES

Ingestion
If swallowed, wash out mouth with water. Do NOT induce vomiting. Drink at least two (2) glasses of water. Seek medical attention.

Eye
Wash with copious amount of water for 15 minutes holding eyelid(s) open. Take care not to rinse contaminated water into non-affected eye. Seek medical attention.

Advice to Doctor
Treat symptomatically

Find Out More

Jan 04

ACRYLOC ROLL ON TEXTURES

PRODUCT TYPE PACKAGING NOMINAL WEIGHT
Texture Coats 5L, 15L Heavy Duty Plastic Pail 7kg, 21kg respectively

DESCRIPTION

Forming part of the Wallcote system, Acryloc Roll On Textures are a range of low to medium profile granular coatings, designed to be applied with a roller. A range of textured effects can be achieved using selected roller covers.

Acryloc Roll on Textures are available in three grain sizes coatings, manufactured as tintable, white bases and provide an attractive finish on correctly prepared domestic & commercial, exterior & interior wall surfaces.

FEATURES & BENEFITS

Excellent water resistance Prime
Excellent vapour permeability Acryloc Prime Seal
Excellent durability Joint Set & Beads/Trims (if required)
Strong adhesion Acryloc Patch (add 5-10% cement)
Low maintenance Fill / Patch / Skim (if required)
Easy to apply Acryloc Patch
Water based, Easy & safe clean up Render Coat (if required)
10 yr Coating System warranty Wallcote FR, for AAC, polymer modified, fibre reinforced
Tintable Wallcote Pro Render, polymer modified, low – medium build
Wallcote Trade Render, traditional Render, medium – high build
plus Acryloc Liquid Bond (if specified)
Texture
Tuscan Fine/Moroccan Medium/Rustic Coarse
Protective Colour Coat (recommended)
Acryloc Armourflex Masonry Matt or Lo Sheen

SUITABLE SUBSTRATES – when properly prepared

  • Cement Render
  • AAC (Autoclaved Aerated Concrete)
  • Fibre Cement Sheeting (Fibro/Blue board)
  • Rendered expanded polystyrene
  • Clay and Concrete Brickwork
  • Concrete blocks
  • Tilt panel walls
  • Other primed exterior surfaces

SUBSTRATE PREPARATION

  • Areas not to be coated should be masked and protected.
  • All surfaces to be coated must be clean, sound, free from contaminants including; oil, mould release, dust, dirt, silicone, mud, grease, salt, efflorescence, animal droppings and any loose or flaking material.
  • All substrates must be primed with Acryloc Prime Seal.
  • Apply the Prime Seal at the rate of 12.5-16.5m2/L and allow to dry (approx 30mins).

(Note: The concentrate form of Prime Seal must be diluted before use)

  • Imperfections and butt joints should be filled with Acryloc Patch with 5% Portland Cement added.
  • The surface may be coated with Acryloc Patch or Acryloc cement based Render, as required, before applying Acryloc Roll on Sand Texture.

APPLICATION

  • Acryloc Roll on Texture does not require thinning or dilution. Up to 300mL of clean water can be added to a 15L pail to adjust the workability if desired.
  • Mix thoroughly with a broad, flat stirrer, using an upward lifting action, or use a power mixer.
  • Power mixing is recommended as this will enhance the workability and give the best coverage.
  • A wet edge should be maintained throughout the application and day joints formed at corners, expansion joints or mouldings where they will not be evident after completion.

METHOD

  • Apply Acryloc Roll on Texture to the surface with a suitable texture roller. Load the roller generously and apply in strips 500mm-750mm in length.
  • Once five (5) or six (6) strips have been applied, roll across to even out the surface.
  • Finish in one direction for an even texture.
  • Repeat the above steps, only re-rolling 70-100mm into the previously coated area.
  • Work quickly and without interruption, laying off from the edge to avoid texture imperfections.
  • If a small area is missed, it is best to touch up when the area is dry. Running out of material midway through a wall surface should be avoided at all times. In this event, feather the edge and allow texture to dry, then marry in with new material.
  • Acryloc Roll on Texture should not be extended (spread) too far; otherwise durability and hiding power may suffer.

Important Notes

  • Care should be taken to keep Acryloc Roll on Texture off windows and adjacent surfaces that are not to be coated, as it can be very difficult to remove once allowed to dry.
  • Do not apply Acryloc Roll on Texture when rain is anticipated within 5 hours of completion of the days work, longer in damp, cold +/or humid conditions.
  • Avoid application in full sun, on hot surfaces or in hot windy conditions.
  • Application should be carried out on a day with temperatures above 10°C and below 32°C.
  • Coated area must be protected from damage until the completion of the project; finished work must be protected from rain, frost and severe weather conditions until fully dried.
  • Acryloc Roll on Texture is normally over coated with Acryloc Acryloc Armourflex for best colour accuracy, to improve durability and to reduce dirt pickup.

Clean-Up

Clean up with water

OTHER CONSIDERATIONS

Shelf-Life – Unopened Containers

Maximum two (2) years from date of manufacture when stored correctly.

Transport & Storage

Pails should not be stacked more than three (3) high during transportation and must be transported upright.

Store in a cool place, upright, out of direct sunlight and above 4°C.

For further information refer to MSDS for Acryloc Roll on Sand Texture.

TECHNICAL DATA

APPEARANCE Off white textured viscous liquid
ODOUR Low
APPLICATION METHOD Roller
SPECIFIC GRAVITY (NOMINAL) 1.4 -1.6
THEORETICAL COVERAGE 1.7-2.0m²/L Tuscan; 1.4-1.7m²/L Moroccan; 1.2-1.5m²/L Rusti
WET FILM THICKNESS (RECOMM) Product grain size
DRY TIME (25°C & 50% RH)(APPROX) Tack Free Recoat/ Overcoat Fully Dried
2 hours After 3 hours 24 hours
NO. OF COATS Typically 1 coat
GLOSS LEVEL Textured – matt

WARRANTY

Acryloc Building Products provides a material replacement warranty against bubbling, peeling or flaking of the full Wallcote Coating System caused by any defect in manufacture for a period of ten years when applied correctly by a skilled and experienced applicator in accordance with all current application criteria, including but not limited to, substrate type and preparation, application rates and methods, prevailing weather conditions and protection of finished work.

Application dates, product batch numbers and quantities must be recorded and supplied as a minimum to effect potential product failure investigation.

Acryloc Building Products provides no warranty, expressed or implied, against damage due to movement of the substrate or structure.

Acryloc Building Products cannot accept responsibility for variations in colour, strength, appearance or workability resulting from on-site mixing procedures and conditions.

SAFETY & HANDLING

When working with Acryloc Roll on Sand Texture observe the usual precautions for handling acrylic water based products including:

  • Avoid inhalation of the vapour, prolonged skin contact and particularly eye contact.
  • Wear protective clothing to minimize skin contact and wear goggles where splatter is likely.
  • Where spills occur, soak up liquid spillage with sand/sawdust and dispose of in a sensible manner. Do not permit run-off to sewer, storm water or open bodies of water.

Full pails are HEAVY. Wear protective footwear and seek assistance if necessary.

FIRST AID MEASURES

Ingestion

If swallowed, wash out mouth with water. Do NOT induce vomiting. Drink at least two (2) glasses of water. Seek medical attention.

Eye

Wash with copious amount of water for 15 minutes holding eyelid(s) open. Take care not to rinse contaminated water into non-affected eye. Seek medical attention.

Advice to Doctor

Treat symptomatically

Find Out More

Jan 04

ACRYLOC ARMOURFLEX EXTERIOR ACRYLIC

PRODUCT TYPE PACKAGING NOMINAL WEIGHT
Exported Paints – EXP401 & EXP405 5L, 20L Heavy Duty Plastic Pail 8kg, 30kg respectively

 DESCRIPTION

Acryloc Armourflex Exterior Acrylic is a durable, water based impact coating, designed to provide fashionable colour and long-term external protection for all masonry surfaces. Armourflex Exterior Acrylic is available in both matt and low sheen finishes.

A range of attractive effects can be achieved using specialized rollers and the high film build makes Armourflex Exterior Acrylic ideal for coating surfaces such as fibreboard, acrylic based textures, cement render and tilt panel walls.
Armourflex Exterior Acrylic is supplied as tint bases to distributors and in tinted, ready to use form to end users. Over 2000 colours are available using our tint system.

FEATURES & BENEFITS

  • Excellent flexibility & crack resistance
  • Water based
  • Excellent durability
  • Tintable to a wide range of colours

SUITABLE SUBSTRATES – when properly prepared

  • Clay and Concrete Brickwork and Blocks
  • Texture Coat
  • Concrete Walls
  • Tilt panel walls
  • Cement Render
  • Softwood timber
  • AAC (Autoclaved Aerated Concrete)
  • Other primed exterior surfaces
  • Fibre Cement Sheeting (Fibro/Blue board)
  • Rendered expanded polystyrene

SUBSTRATE PREPARATION

Note: If applying Armourflex Exterior Acrylic on freshly applied Acryloc Texture, no further preparation/priming is required

  • Areas not to be coated should be masked and protected
  • All surfaces to be coated must be clean, sound, free from contaminants including; oil, mould release, dust, dirt, silicone, mud, grease, salt, efflorescence, animal droppings and any loose or flaking material
  • All substrates other than freshly applied texture must be primed with Acryloc Exterior Primer, EXP102.
  • Apply one coat of Acryloc Exterior Primer and allow to dry (approx 45mins)

APPLICATION

  • Armourflex Exterior Acrylic may require thinning, depending upon the application method used. Up to 1L of clean water may be added to a 15L pail (~6.5%) without the need to apply any extra coats. Thorough mixing is essential. Greater than 7% addition is not recommended.

Method

  • Mix thoroughly with a broad, flat stirrer, using an upward lifting action, or power mixer and check that the colour is correct before commencing work.
  • Care should be taken to keep Armourflex Exterior Acrylic off windows and adjacent surfaces that are not to be coated, as it can be very difficult to remove once allowed to dry.
  • Acryloc Exterior Acrylic can be applied using a roller, brush, pad, HVLP spray equipment or airless spray equipment.
  • If using a roller, roll the coating in one (1) direction only, to avoid cross masking of layers
  • If using airless spray equipment, a 19-21 thou tip and white gun filter is recommended. Try to maintain a Wet Film Thickness of 100-125µm for each single coat by checking regularly with a Wet Film Thickness Gauge.

Coverage

Surface Per Coat Recommended Coats
Wet Film Thickness Apply at Coverage
Smooth, fine render/texture 100-125 microns 8-10 m2
per Litre
120-150 m2
per 15L Pail
1-2
Rough, coarse texture 4-5 m2
per Litre
60- 75 m2
per 15L Pail
1-2

Clean-Up

Clean up with water.

Important Notes

  • Do not apply Armourflex Exterior Acrylic when rain is anticipated within 5 hours of completion of the work, longer in damp, cold +/or humid conditions
  • Avoid application in full sun, on hot surfaces or in hot windy conditions
  • Application should be carried out on a day with temperatures above 10°C and below 32°C
  • Coated area must be protected from damage until the completion of the project; finished work must be protected from rain, frost and severe weather conditions until fully dried.

OTHER CONSIDERATIONS

Shelf-Life – Unopened Containers

Maximum two (2) years from date of manufacture when stored correctly.

Transport & Storage

Pails should not be stacked more than three (3) high during transportation and must be transported upright Store in a cool place, upright, out of direct sunlight and above 4°C
For further information refer to MSDS for Armourflex Exterior Acrylic

TECHNICAL DATA

APPEARANCE Coloured viscous liquid
ODOUR Low
RESIN TYPE 100% pure acrylic emulsion
APPLICATION METHODS Roller, brush, spray
SPECIFIC GRAVITY (NOMINAL) ~ 1.4
DRY TIME (25C & 50% RH) (APPROX) Tack Free Recoat/ Overcoat Fully Dried
1 hour After 2 hours 24 hours
GLOSS LEVEL Matt and low sheen available

 SAFETY & HANDLING

Observe the usual precautions for handling acrylic water based products including:

  • Avoid inhalation of the vapour, prolonged skin contact and particularly eye contact
  • Wear protective clothing to minimize skin contact and wear goggles where splatter is likely
  • Where spills occur, soak up liquid spillage with sand/sawdust and dispose of in a sensible manner. Do not permit run-off to sewer, storm water or open bodies of water

Full pails are HEAVY. Wear protective footwear and seek assistance if necessary.

FIRST AID MEASURES

If swallowed, wash out mouth with water. Do NOT induce vomiting. Drink at least two (2) glasses of water. Seek medical attention.

Eye

Wash with copious amount of water for 15 minutes holding eyelid(s) open. Take care not to rinse contaminated water into non-affected eye. Seek medical attention.

Advice to Doctor

Treat symptomatically

Find Out More